No similar topics found.
0
Configure video priority
Is it possible to configure the video priority level in IQAN Design? Sometime I may need to set the video as background. It would be good if in IQAN Design allowing me to set the layer of the video.
0
Fixed
Linear or circular bar animation crash program
Tuomas 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
6
-Design latest version
-MD4-5 display
-When using linear or circular bar the program crash down
-Only fixing by removing these elements
I believe these elements animation cause this because when bar animation goes to end then program will crash. Can you disable animation from these elements?
0
Answered
SAE J 1939
Masia Jean-Baptiste 11 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
2
Hello
On a original Tigercat vehicule
,
We can find :one MD3 ,one XA2 , one XS2. The Md3 send (TSC1 : SAE J 1939 frame) and receive SAE J1939 from the ECU.
see the original drawing:
My custumer want to add one MD3 and one MC2 in the tigercat to drive one other accessories
my system:
My VIN must accelerate the engine and my proportionnal outputs. ( automotive system )
We would to like a new MD3 ( MD3(2) ) send a TSC1 (SAE J 1936 frame) and the old MD3 receive SAE J 1939 frame CAN . We have affraid that the engine received 2 TSC1 message and the engine stop !!! ( conflict !!!!!! )
I don't have the original program of the vehicule (picture (1) MD3, XA2, XS2).
Do you have a solution for stop the TSC1 transmission on the original MD3 or other solution?
Please feel free to contact me if you have any questions .
On a original Tigercat vehicule
,We can find :one MD3 ,one XA2 , one XS2. The Md3 send (TSC1 : SAE J 1939 frame) and receive SAE J1939 from the ECU.
see the original drawing:
My custumer want to add one MD3 and one MC2 in the tigercat to drive one other accessories
my system:
My VIN must accelerate the engine and my proportionnal outputs. ( automotive system )
We would to like a new MD3 ( MD3(2) ) send a TSC1 (SAE J 1936 frame) and the old MD3 receive SAE J 1939 frame CAN . We have affraid that the engine received 2 TSC1 message and the engine stop !!! ( conflict !!!!!! )
I don't have the original program of the vehicule (picture (1) MD3, XA2, XS2).
Do you have a solution for stop the TSC1 transmission on the original MD3 or other solution?
Please feel free to contact me if you have any questions .
0
Answered
Sequential execution/validation
David Dufour 11 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
8
Hi,
I need to find the best method to do a sequencial communication.
Actually I need to send canopen packet in order and I need to respect this order.
As I can have multiple item, required or not (enabled/disabled) to send.
Case 1:
For example, with a scanreco remote control LCD screen I need to :
- Clear screen
- Activate FrameID of each component required to be visible on the screen
- after this I'll need to update each FrameID value with a 250ms timing.
Actually I was able to do this for testing purpose, but the program is a bit messy.
Case 2:
Sequential safety validation. Each step need to be validated in a specific sequence and in case of condition lost, I'll need to start again from the first step.
- Press "bypass" mode status on the screen
- Open the fence (Signal OFF)
- Close the fence (Signal ON
- Open the door (Signal OFF)
- Close the door (Signal ON)
- Activating bypass activated signal
In case of lost of the fence or door signal, I need to restart from the beginning this sequence.
I have in mind to use IDC + counter to do this, but I'm not sure to be in the right way.
I'm looking if you have example or recommendation to do this ?
I'm sure you notice that it's my very first project!
Best regards,
David
I need to find the best method to do a sequencial communication.
Actually I need to send canopen packet in order and I need to respect this order.
As I can have multiple item, required or not (enabled/disabled) to send.
Case 1:
For example, with a scanreco remote control LCD screen I need to :
- Clear screen
- Activate FrameID of each component required to be visible on the screen
- after this I'll need to update each FrameID value with a 250ms timing.
Actually I was able to do this for testing purpose, but the program is a bit messy.
Case 2:
Sequential safety validation. Each step need to be validated in a specific sequence and in case of condition lost, I'll need to start again from the first step.
- Press "bypass" mode status on the screen
- Open the fence (Signal OFF)
- Close the fence (Signal ON
- Open the door (Signal OFF)
- Close the door (Signal ON)
- Activating bypass activated signal
In case of lost of the fence or door signal, I need to restart from the beginning this sequence.
I have in mind to use IDC + counter to do this, but I'm not sure to be in the right way.
I'm looking if you have example or recommendation to do this ?
I'm sure you notice that it's my very first project!
Best regards,
David
0
Answered
When is IQAN Design 3.15 due to be released?
Kevin 11 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 11 years ago •
2
We are waiting for a couple of fixes to be released in 3.15, and I think 29th January was mentioned previously for the release of the updated software, can you confirm when its being released please?
0
Answered
Multitouch Functionality on MD4
Richard Staite 11 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 11 years ago •
3
Can you give me any pointers as to whether it is possible to achieve multi touch functionality on the MD4. I need to be able to activate two on screen buttons simultaneously and in this case toggling one and then activating the other is not really appropriate.
Incidentally it would be nice on Virtual digital inputs to be able to reset the toggle by means of an external channel - so that the button stays depressed (colour changed) until it is reset either by touching it again or by the channel selected.
Incidentally it would be nice on Virtual digital inputs to be able to reset the toggle by means of an external channel - so that the button stays depressed (colour changed) until it is reset either by touching it again or by the channel selected.
0
Fixed
Bug: Conflicting windows
Jean-Marc Zanni 11 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
3
I was working with the Navigator window opened in the center of my screen, working on logic. I mistyped the variable and the type ahead error Pop-up appeared. But it was behind the navigator page. I could not close the navigator or reach the pop-up. I had to kill the application to unlock the system.
I would also suggest that this lookahead error pop-up is very annoying. If I mistype one letter (which happens often) it shows up I have to switch to the mouse to clear. Why not wait until I press the tab button to give me a chance to correct my typing mistake?
I would also suggest that this lookahead error pop-up is very annoying. If I mistype one letter (which happens often) it shows up I have to switch to the mouse to clear. Why not wait until I press the tab button to give me a chance to correct my typing mistake?
0
Answered
Can you pick up open load and overload only errors on MC3 outputs?
We need the system to display an error message and restrict certain functions only when an open load or overload of an output occurs on an MC3 controller.
The only way of picking up an error message appears to be in the system information function, but this seems to be a blanket error flag that could be a fault with any part of the control system (including v ref, batt voltage etc). We would ideally only like to pickup on an open load or overload.
I see there is module status, but that only shows 9 different items. Is there an option to pick up on only the open load and overload error of an output on an MC3?
The only way of picking up an error message appears to be in the system information function, but this seems to be a blanket error flag that could be a fault with any part of the control system (including v ref, batt voltage etc). We would ideally only like to pickup on an open load or overload.
I see there is module status, but that only shows 9 different items. Is there an option to pick up on only the open load and overload error of an output on an MC3?
0
Fixed
Not saving Function group input when Public variable are used
Jean-Marc Zanni 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
3
I have set-up some variable as public in a function group. In another function group I am using one of those public variable as input to a function group
When the program run correctly. But if I change the software and or save and close the next time I open the project the assignment disappear and I get an compile error for an undefined input to the function group.
0
Answered
Iqandesign with Windows 10 on Surface Pro 4
Has anyone tried using Iqandesign with a Surface Pro and Windows 10? Do the drivers work for USB (MD3) and ethernet (wireless) for MD4. I travel quite a bit and would like to reduce the weight of my computer/charger.
Customer support service by UserEcho
