BSOD on MD4
It did not seem to happen in 3.14.
I have tried updating to 3.18 as there seemed to be some fixes for Blue screen problems but it is still happening.
XC10 output high in software but low directly on module
We experienced a similar issue with output energisation that was corrected in 3.16 but this is slightly different.
System is 1 MD4 with XC10 as expansion, 1 MC3 and 1 MC3 with XC10 expansion. We have logic that switches a single DOUT on XC10 expansion connected to MD4. This logic is handled in MD4 application. With a delay on of 500ms or less the output on XC10 remains low on module (tested using multimeter) but IQAN design when connected says high.
If I increase delay on to 1000ms the output switches on and voltage present on XC10 module using multimeter.
Its almost as if the MD4 is sending a command to energise output before XC10 has booted?
I have rigged up single MD4 and XC10 on the bench but been unable to replicate, perhaps cycle time of the software could be the issue? Running IQAN Design 3.19.
Trial License - what does it permit and prevent - document this
During installation, it mentions connection only with simulator, etc. This is very clear and defined , but only available during installation. If this could be added to the manual or a separate document this would let us have a standard answer for customers.
Cycle time effects timer counting 3.18
When I reduce the cycle time of the application down to 5ms the time taken to get to 10000ms in the MC3 application takes approx. 20000ms in real time. Its almost as if the timer counting has slowed down when I reduce the cycle time.
I have tried as a new application file with simply just a timer counter in and no other logic as I wondered if I was approaching the processing limit but the inaccuracy still appears present?
I haven't tried previous versions of software and been unable to test in a real application so I can only assume this could be an issue with simulate and not IQAN Design?
rotating picture
It is possible to rotate a picture with a mathematical function ?
best regard
What kind og iqan?
hello and thanks for this great forum.
A have an 2001 IllerIller tdi tracked vehicle, made in Sweden. The driving system is controlled by a iqan system. I attached a picture of the screen. Is there anybody how can tell my what version of iqan it is, and what software a need for adjust parameters? I find a rs232 cable behind the seat, and I guess it is for programming iqan.
Unsuccessful MD4 program update using IQAN Design 3.15
New to forum. Looking forward to all the knowledge base available here.
To kick it off, I have encountered a situation where loading of an IQAN Design program from version 3.15 into an MD4 proves unsuccessful. IQAN Design will load firmware resources 21/21 and gets hung up on "Waiting on MD4". While on the MD4, there is a blue screen with the last line of text saying "CRC OK". I've let it sit there for 20 minutes with no change in status.
However, when loading a IQAN Design program from version 3.11 (have not tested 3.12 - 3.14) to the same MD4, no blue screen. Is this is a known bug and will it be addressed in 3.16? Is there a workaround in the meantime?
Thank you all in advance and once again, looking forward to forum.
-Manny
Module communication failure when updating to V3.19.9
We have a system (2 x MC£, 1 x MD4) running V3.19.7 and decided to update to version 3.19.9. Sent program over CAN communication tool and machine appeared to update to 3.19.9. After completion of update one module wasn't communicating over the master bus. This isn't unusual. We cycled ignition (which usually fixes error) and the module still failed to communicate. We have got this module into an endless cycle giving CAN error. Is this as a result of updating from 3.19.7 to 3.19.9?
event counter reset reverting to the wrong number - suspicious possibility
It has happened a few times to me.
Distribute vertical - MD4 7 with 3.15 - bottom object doesn't distribute evenly
Using an MD4 in 3.15, did not see a patch note that this was fixed or a post.
Hope it is not redundant to mention.
Customer support service by UserEcho
