No similar topics found.
0
Answered
IQAN Design 3.15
Kevin 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
1
When is 3.15 being released? We are keen to have the fix for the latching button issue on the MD4 display?
Answer
Ulrik Zakariasson (Software development)
10 years ago
IQANdesign 3.15 is planned for release in about a week, January 29 to be exact. The latching button issue has been fixed and will be part of the 3.15 release.
0
Answered
How to get text over images in IQAN Design 2.63?
I am using IQAN Design 2.63 and I am trying to figure out how to get text to show up on top of images on the screen. No matter how I have the order set in the "Set Order" window, text always hides behind images.
0
Automatic entry of State machine labels when used as module input
When a state machine or state parameter is defined as a module input you have to manually add all the states. It would be nice if we could at least automatically import them from the previous layer. Would save tons of programming time.
I can understand that someone may want the ability to have different description for each state, but it is pain fully slow to re-create each states.
I can understand that someone may want the ability to have different description for each state, but it is pain fully slow to re-create each states.
0
Answered
Showing a "PDF Loading" Message or Some Indication on MD4
Daniel Grant 9 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 9 years ago •
2
Our customer is impressed by the PDF capability, but wants some way to see that the PDF is loading.
I want to have my "User Manual" button to do one of the following things:
- Have the button stay in a pressed state until the PDF loads up.
- Use a separate VDIN that commands the PDF to open up.
- Show a message indicating that it is loading.
Any help would be very appreciated!
0
XC10 output high in software but low directly on module
We experienced a similar issue with output energisation that was corrected in 3.16 but this is slightly different.
System is 1 MD4 with XC10 as expansion, 1 MC3 and 1 MC3 with XC10 expansion. We have logic that switches a single DOUT on XC10 expansion connected to MD4. This logic is handled in MD4 application. With a delay on of 500ms or less the output on XC10 remains low on module (tested using multimeter) but IQAN design when connected says high.
If I increase delay on to 1000ms the output switches on and voltage present on XC10 module using multimeter.
Its almost as if the MD4 is sending a command to energise output before XC10 has booted?
I have rigged up single MD4 and XC10 on the bench but been unable to replicate, perhaps cycle time of the software could be the issue? Running IQAN Design 3.19.
0
Answered
rotating picture
Masia Jean-Baptiste 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 8 years ago •
10
Hello
It is possible to rotate a picture with a mathematical function ?
best regard
It is possible to rotate a picture with a mathematical function ?
best regard
0
Fixed
Unsuccessful MD4 program update using IQAN Design 3.15
Manny 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 10 years ago •
6
Hello all,
New to forum. Looking forward to all the knowledge base available here.
To kick it off, I have encountered a situation where loading of an IQAN Design program from version 3.15 into an MD4 proves unsuccessful. IQAN Design will load firmware resources 21/21 and gets hung up on "Waiting on MD4". While on the MD4, there is a blue screen with the last line of text saying "CRC OK". I've let it sit there for 20 minutes with no change in status.
However, when loading a IQAN Design program from version 3.11 (have not tested 3.12 - 3.14) to the same MD4, no blue screen. Is this is a known bug and will it be addressed in 3.16? Is there a workaround in the meantime?
Thank you all in advance and once again, looking forward to forum.
-Manny
New to forum. Looking forward to all the knowledge base available here.
To kick it off, I have encountered a situation where loading of an IQAN Design program from version 3.15 into an MD4 proves unsuccessful. IQAN Design will load firmware resources 21/21 and gets hung up on "Waiting on MD4". While on the MD4, there is a blue screen with the last line of text saying "CRC OK". I've let it sit there for 20 minutes with no change in status.
However, when loading a IQAN Design program from version 3.11 (have not tested 3.12 - 3.14) to the same MD4, no blue screen. Is this is a known bug and will it be addressed in 3.16? Is there a workaround in the meantime?
Thank you all in advance and once again, looking forward to forum.
-Manny
0
Fixed
event counter reset reverting to the wrong number - suspicious possibility
Does anyone else seem to have a gremlin changing your event counter reset values?
It has happened a few times to me.
It has happened a few times to me.
0
Not a bug
Distribute vertical - MD4 7 with 3.15 - bottom object doesn't distribute evenly
Zach 10 years ago
in IQANdesign
•
updated by Ulrik Zakariasson (Software development) 9 years ago •
7
I will see an even spacing between all except the last object when using the vertical distribute button.
Using an MD4 in 3.15, did not see a patch note that this was fixed or a post.
Hope it is not redundant to mention.
Using an MD4 in 3.15, did not see a patch note that this was fixed or a post.
Hope it is not redundant to mention.
0
Separate On State Text and off State Text on Text Buttons on MD4
When you use a text button on an MD4 it would be nice to have different text fields available for the On state and the Off State.
I have tried to use the Text Button but with no text in it, and then place text over the top of it which is enabled with another channel, but no matter where you put the text channel in the display order, the on state colour still covers the text when you toggle it on (on the simulator - I've not tried it on the hardware yet)
I have tried to use the Text Button but with no text in it, and then place text over the top of it which is enabled with another channel, but no matter where you put the text channel in the display order, the on state colour still covers the text when you toggle it on (on the simulator - I've not tried it on the hardware yet)
Customer support service by UserEcho
