Changing default language
Hello all,
I received a project that I need to revise. This project contains many translations (in software and display). The default langauge is set to Dutch however. I would like to use English in the software. Is there a way to change the default language, without losing the translations?
Thanks in advance
Reading hz more accurately
i am using a FIN to read an RPM sensor. The sensor has 30 pulses per revolution.
Today we are getting an even value (2-4-6-8 etc.) of off the sensor. in other words 1Hz is the lowest given pulsefrequenzy. ( 1 pulse per second = 2 rev per minute 1*60/30 )
i would like to be able to read half an rpm, or even 1 rpm steps would work ( 0,5Hz )..
is this possible?
i know i could average an Array, but i would assume the FIN could give me a more accurate read, with less delay?
Robin
Generic Bus and Generic Modules
Is there an upper limit, maximum number, of generic modules that can be configured on a single generic bus for an MD4 controller?
CAN Routing
It looks like you guys added CAN routing for the MC4x family in IQAN 5, but there is no documentation of it anywhere that I can find.
So my setup is a Generic 500k CAN bus that has 10 modules on it. I need to place a router in front of one of the modules to block a few CAN ID, so I can broadcast it a different set of data. The module that is behind this CAN router is also sending out its own messages to the rest of the network that the other 9 modules need to see.
So do I set up 2 routing rules? One to go from A to B, and then B to A.
Or how would I go about setting up the CAN routers to make this possible?
This is what I have right now. There is one ID i need to block from the ECU to Trans, and then the Trans to ECU will all be allowed. Will this setup work like I am wanting it to?
MC43 functional safety
Is there any news on when the MC43 functional safety is hoping to be completed?
Upload aplication (and firmware) with iqansync
Hello.
I need to upload a Project to a machine with MD4+MC2 (via iqansync). The project was uploaded fine to the MC2, but I can't upload the project to MD4. It goes fine until 50%, but then starts to upload the firmware, and finally it stops and gives an error message. The size of the Project is 25mb.The original Project I suppose was made with 4.03 and the new one was made with 4.07.
Is there any possibility to upload Project (or at least firmware) with a usb pendrive or memory card?
Inconsistent Logging
I have two duplicate event logs, each with several of the exact same log items in them, with the same triggering logic and channels etc... but with different access rights so service can't clear one of them.
When I receive a clone from a machine and check it's logs the values stored in either log are often different. In some cases the value is not even recorded or the event wasn't triggered in the second log. Is it possible a high (nearing alarm point) utilization rate can cause this or is there something else to blame?
MD4-7 Blue Screen
I am getting a blue screen on a program I wrote with IQAN 5 and an MD4-7.
The program starts and functions normally and then 10 seconds after start up I get this screen.
Touchscreen internal channel
Hi,
Is there an internal channel that goes on and off if someone touches the screen?
If so, can I use it?
I want to dim the screen when the system is standby for a long time and for that I know I can use the backlight control, but I also want to remove the dim if someone touches the screen to "wake" it up.
Is this possible?
Thank you
MD3 Firmware Problem?
We currently have 4 MD3s that are 8 years old. When trying to upload an IQAN project file using a USB to CAN adapter they give no response, only error messages are transmitted to the CAN bus. I know my setup is wired correctly and there are no problems with it because I'm able to upload a project file to a different MD3 that our distributor put new firmware on a few years back.
Is this a firmware problem? if so, How is new firmware downloaded into an MD3?
Customer support service by UserEcho