In Variants projects using IQANdesign the import settings option is disabled.

Why is it disabled in these projects?

Hello,

When propagating several outputs from a function group, 

you have to right click and go to "propagate outputs" and select the outputs to propagate.

But when you have more than 10 outputs to propagate, it's very long to do it each time.

Maybe could you let the menu open, and lets us to click on all outputs we need to propagate ? and the menu close when clicking on the page

or maybe something like, allow multi click by holding CTRL key ?

We have 12 values being logged every second, and I have downloaded the log to find that every 4 minutes and 15 seconds the time counter resets back to 2 hours and starts counting again at 02:00:00. Weirdly earlier results (an earlier index number) also appears to have the same behaviour around 01:00:00 and then it strangely jumped to 02:00:00. It then continues to go back to 02:00:00 every 4 minutes 15 seconds.

I understand the MC43 does not have a clock and we know start 154 is the information I need to extract, but I would have expected the timer to begin at 00:00:00 and carried on counting up until the ignition was cycled and log stated 'Start 155'.

Can I assume they are all in the correct order based on the index value rather than the time? ie. greater index value = most recent log and timer counting is not relevant?

See below a similar record earlier where it jumps from 01:00:00 to 02:00:00:

The log is set to recycle so can hopefully discount filling up the controller and it not being able to handle the quantity. This log is set to occupy 95% of the log memory.

IQAN 6.08.

After setting up project as variant with Variant Option Select, when I export I receive Invalid Context Error.

Do all channels into a "Variant Option Select" have to have same name for it to work? as that only thing I can come up with after examining those that don't error 

Basically the question. I am trying to get the bit and byte numbering to start at 0 instead of 1 in the J1939 frames.

As far as I can tell, there is no way to show Qcode or the object list in the generated project documentation. If there is a way, please point me in the right direction. If there isn't, it would be a nice feature to have in the next release.

I have an application using a  MD4/7 screen with MC43FS master, on start up the first screen loads OK, but when I change between screens for the first time it takes a while to load the next page, after the first time, in subsequent changes the delay is not present, Is there any way / any tricks I can use to reduce this initial delay? or is it just a product of size of the graphical content that has to be loaded? 

Hello,

I am working on an external function for a battery system.

Basically, we have many "Slave BMS" on our network and I want to see the cell voltage that they all send me thought CAN Messages. The thing is that those information are sent thought a multiplex message. So, I've used your Paged Protocol feature to indicate which data contained what I wanted and it has worked really well.

Now I want to assign a parameter to the page value. like that when I use that external function, I can setup different BMS_ID depending on my setup. However, it seems to only accept number. Is it me that is not using the correct type of channels?

Thank you for your time,  

MD4 running 7.01

When calling up a PIN code entry and it sits partially over a button behind, failure to enter correctly (so the keypad disappears) seems to show a graphical bug, one on the IQAN enter pin message button, and one on the partially blocked 'SETUP' button we have on a screen.

Doesn't appear to affect functionality so purely aesthetics.

I dont see any error during a project check, most lines are grey but a couple red.

Oddly it came around, I had an unused value from a can message and deleted it, that set the can message red,  claiming it wasnt connected back to the system layout, no amount of dragging and dropping fixed that, the only option was to delete the whole can message and re-add it. This strikes me as a bug anyway (surely I should be able to remove an unused value without breaking everything - I can add one without breaking everything). But what is the red trying to show me and how can I find out?