Hello,

I purchased the IQAN Run software and install the license key into my laptop by mistake. I want to put the license key into my colleague's laptop but unfortunately it is not allowing me to register it. Is there is any way to put the license key to my colleague's laptop?

Thank you

Hi,

I haven't received an email with the correct key for the 10 bluetooth connections with IQAN RUN, where can I see my key? I can't work without these connections.

Thank you.

Best regards,

Lorenzo Simonetti

I am working with a file that has many settings and it would be nice to be able to save the settings file in a format that would allow saving in a spreadsheet.  This would allow a user to be able to sort through the information much easier.  Is there currently a way to save a settings file in a spreadsheet or similar format; any type of workaround to get the settings file information into a spreadsheet?

Hi everyone,

Is there someone that could help for my work for a client

Kind regards,
Richard Kowalczyk MIEAust CPEng(Ret)
RKad Engineering
32 Kingussie Ave
Castle Hill NSW 2154
Australia
📲 :+61 (0)431 639 295

E: richard.kowalczyk@rkad.com.au
W: www.rkad.com.au

Hi everyone,

I would like to attract your attention to the problem that i have encountered as described below:

I have been working to convert input from Wema type fuel level sensor (resistance output) converting it into VIN for MD3 input using volt divider. After calibrating actual device I have defined 2 square curves (0-50% and 50%-100%) to get better accuracy. IQAN program attached (.FuelLevel.idax). When I opened this program in IQANDesign 5.08 I have got the following result when simulating on computer which you can see it is wrong result as and simulation would give only -039 or 1.04.

If I load program in this stage into machine it would behave incorrect as in simulation

Then after playing with it I have discovered that closing simulation and then editing 'Default function' for M_Fil (Math channel) for example changing "-0.39" into "-0.391" and then back into "-0.39" and then restarting simulation it would come back to normal (what i would expect) as you can see on the following picture

When I have loaded the program into machine in this stage it has been working ok since then.

Additional info:

Your comments will be much appreciated

Kind regards,
Richard Kowalczyk MIEAust CPEng(Ret)
RKad Engineering
32 Kingussie Ave
Castle Hill NSW 2154
Australia
📲 :+61 (0)431 639 295

E: richard.kowalczyk@rkad.com.au
W: www.rkad.com.au

It might be interesting to think about a way to structure the software so you can easily generate corresponding flowcharts and or state machine diagrams based on it. This would save a lot of time when communicating with people that are not familiar with the IQAN software architecture and makes documenting the software a lot easier than manually creating the flow charts ourselves. Again this is just something that came to mind and would love to know what people think about this kind of feature and if this is even plausible.

Thank you in advance!

Hello.  I am a new IQAN user and I am having difficulties.  I found at power up that I had a flashing IDTag error (it is not obvious in the sales literature that one was required) plus I cound not establish a connection via CANbus.  I am using a Kvaser Leaf Lite as my interface.  I read in a forum on this site that the tag resistance for address ) is 294 ohm.  I plugged in a 278 ohm resistance and the issue remained.  I havefour questions:

1.  What is the tolerance on the address resistance value?    

2.  Does this error prevent establishing a connection with a PC over the CANbus?

3.  Does the interface GND need to be connected to the IQAN-MC41 GND?

4.  Does the CAN-A and CAN-B configuration setting need to be set to terminated?  My controller is operating as a stand alone device.

Any help I could get on this would be appreciated.  Thanks.

Hi Guys

Im relatively new and a bit surprised that many of the IQAN modules contain Real Time Clocks that are potentially set with current date and time but nothing in Qcode or design is set up to allow use of that time? (I think)

Let me give you a scenario, Im building a system for managing a  mobile grinding plant where the onboard engine is circa 1200hp. Engines that big need Prelude to be provided before start for the first time of the day, or after its been sitting for more than about 3 hours without the engine running.  This avoids teh damage to the bearing surfaces on components that weigh large amounts and over time standing still will exclude lubrication from the bearing surfaces due weight of components.  The thing is that the engine not running occurs at the same time that the iqan modules may well have been shutdown. So only a RTC will understand the amount of time that has passed since the engine last ran. I can probably add a canbus module that has an accessable RTC but why do I need to do this???

I can cheat and just run prelube every time for say 60 seconds before start, but I don't see why I should have to do that when its not necessary. I could also use other things like residual oil temp or residual coolant temp to determine approx when it was last run or to at least save prelube cycles for shutdowns that are less than 15 mins in length

SO is the RTC functionality I'm looking for truly not present or is there some other way of dealing with this that Ive completely missed? 

Andy

Sometimes, if the Component Navigator is open on the secondary screen, when opening the Calculation Order this new dialog window will be without any buttons. Resizing the window does not help.

Even if I close calculation order window and reopen it ten times it still does not have any buttons.

However, if I close and reopen the Component Navigator, then the next time Calculation Order will have buttons again.