I am using a digital output channel on a proportional coil (I ran out of current outs). I would like to be able to adjust the peak time and hold value in an adjust group so I can test my ranges out with out doing a download every time I make a change.

Hi,

I need some advice regarding physical connection of SAE-J1939 between 2 modules fitted on separate machines.

Are there any arguments against to connect it by using RJ45 connectors?

I would like to use a HARTING modular connector with RJ45 insert but I'm not sure if it is a good idea.

Hello.

I think it would be a good improvement if we can give to states in FSM the order that we want (not only be allowed to order states in a list)
In this way, if our fsm has some ramifications, we can use any kind of code to give the order to the state and in this way it would be easier to develop the application.
For example, in this image, if we use 2x numbers to the top line, if we need to add a new state between 21 and 22, and the dout must be active also in the new state, it is easier to have something like inside 20 and 29 than add this new state to active if state=20, state=21, state=22...

Not sure if I'm using FSM in the correct way or there is other way to do this, but FSM works really nice

Hi there,

Does anyone have a video with the image from IQAN SV camera? 

I'm using now a BRIGADE camera but I'm not happy with the quality of image.

Thanks in advance.

Damian

Hello!

I've been reading instruction book, but I'm not sure about this doubt. And have no MC43 at the moment to be tested.

In IQAN Design, when adding an MC43 module to the system, it doesn't have "RTC Enabled" property in its property inspector. But, I doubt if it has no internal RTC, or it does, but can't be disabled.

Does MC43 have RTC?

In case MC43 does NOT have RTC:

Will event logs always register the time from system startup? 

If there's another master in the system with enabled RTC, MD4 for instance, will the MC43 Logs take the time from the MD4 for its event logs?

Thanks!

Has anyone used any hardware to automatically change the back lighting of the IQAN displays (MD5 MD4 and MD3) automatically with the change of ambient light outside on a vehicle? I have a customer asking the best way to do this, any suggestions or assistance from anyone? Please let me know thanks. 

I updated iOS app to 5.01.4 yesterday and now I can not connect to any G11 modem. The app will see the module but when sending file to machine, I get a "Communication interface error" "Could not find services". When going into Bluetooth adapter configuration, it again sees the module but only show 0.00 on firmware, BIOS, and Hardware versions. Prior to this update, everything was working great. System is running 4.07.14.4747 on a MC42.

We have an application where it utilises the maximum capability of an MC43FS. Can we run a second dedicated master bus (probably an MC41FS) directly between the two modules (no other modules connected except MC43FS and MC41FS) to give us full APP IN / OUT and additional performance capability? We would normally just add the MC41FS onto the main master bus but this is handling quite a bit of non safety critical info to an MD4, we just don't want to overload it with safety APP IN / OUT to share safety calculation between modules.

IQAN Design 5.01 does not hint or produce errors when checking the project with two master busses. Does the software know which bus to 'listen;' for a certain module APP IN or OUT?

Hello there,

We purchased two new MR4-7 modules with firmware and Iqan design version 4.03xx. We updated both modules with a machine clone file to version 4.07.7.1413 using Iqan run.

Then we tried to connect with the G11 to the MD4-7 with GSM and Iqan Syn. It was possible to select the machine ID to connect to. After that Iqan sync give a message: no handshake. 

The G11 led was blinking 4xred 2xyellow = Internal errror/G11

We tried with Iqan run for tablets and the problem was the same.

After that, we updated the MD4-7 with the same aplication using Iqan design to version 4.07.15 and then with iqan run back to the clonefile to version 4.07.7 and then the G11 was working correct.

What goes wrong?

Kind regards Laura