Hello,

Is it possible to use 2 touch button at the same time?

For safety reasons I can't make them toggle buttons.

So what I need is to push on Avant (left) & Avant (right) at the same time.

Hello,

We are in process to upgrade our IQAN Design to the latest version 6

we have a Creative Studio Licence and on the Iqan Store I dont know what to choose between:

DRS (Developer Bundle) which cost around 2300€ and include Design/Run/Script or Design 6 (1400€)

under Design 6, there is a text below: If you have an expired license for IQAN Creative Studio or IQANdesign 1.x you can upgrade to a subscription license here. 

So does it mean that under my Creative Licence, only Design will upgrade to version 6 or Run and Simulate will also follow to version 6?

Br

/Adrien

I need some assistance please.  I want to memorise text from the J1939 TPIN, so they when the key is off (ie no J1939) then he text is preserved and disaplyed on the MD4-7 all the time.

The only way I can figure out to get the TPIN value into the Memorising channel is by using a state parameter channel first (SP) as this only accepts states for the text values.  Then I can get the text into the Memorising channel.  I use a IDC channel that looks at the PGN OK status to trigger the Memorising channel to Qreplace.  This stratey works fine for numbers, but not for text

BUT anytime the PGN in frame times out (ie key off), then all the text values go to blank including the Memorising channel, through that entire signal chain.  If I disable the Timeout on the PGN input, then it works, but the project now has yellow warnings for no Timoueouts and this is a messy solution.  

Can anyone please advise how to get J1939 TPIN values Memorised when the datalink is off (and all messages timeout)

Thanks

Julian

Is it possible to use a USB controller to adjust values in IQan Simulate? 

Ideally I'd like to use a midi fader board like the AKAI APC MINI to adjust certain values, without having to click through groups or separate values. 

Anyone done anything like this in the past? 

Cheers, 

Joe

Is there any way to speed up the MD4 firmware update over CAN?

System: MD4-5 + MC43 + XC43, Design version 6.02 -> 6.04.9.

All messages (warnings, alarm, info etc.) are blinking on display IF there are more than 1 message.

Is there a way to use VDIN buttons (obviously not using the toggle feature) to raise and lower a function parameter by the given step size instead of using the slider? 

I have a integer parameter that represents the address of a piece of equipment(MD4 is master) at a site.  There are other identical pieces of equipment at the site that will have different addresses(saved as integer parameters). (all using the same Project)

My issue is, that if someone clones (with settings) the Project from one piece of equipment and loads it into a different piece of equipment, both pieces of equipment will have the same address.  

These pieces of equipment get paired, wirelessly, with common control devices(using J1939), so they have to use the same Project with the MD4 address.  

So, is there a way to stop a parameter value from being copied through a clone(with setting) to a different MD4?

Ideally I would like the parameter to be set to the default until someone goes into the adjust menu and sets it.

If there was a way to stop all parameters from being copy using cloning for this Project, that would be ok too.

IQANgo (running on a Medion tablet) crashes when connected via Bluetooth after a transfer of about 4800KBytes. I have about 5GB free storage on my tablet, more on an SD card but the app does not allow selecting the storage location. No problem getting a smaller file like Settings" Any ideas why?

thannx,

Zachary Shewchuk

Hello,

At the moment the display I have on the touch screen and the display I have created in the iQAN design are completely different.

I need to directly display the user interface pages to the touch screen.

How can I connect my project to the touch screen?

Thank you